济南车库门：车库门遥控器对码的方法和注意事项

来源：http://www.jnyuqilin.com/  发布时间：2024-05-10 11:48:19

　　有了车库最直观的感受就是冬天不用“热车”，夏天不用“蒸桑拿”，不用为找车位而烦恼。但日常使用中难免会丢失车库遥控器，是找专业人维修还是自己动手？其实增配遥控器非常简单，只要学会对码就能轻松解决。对码是车库遥控器增配过程中非常重要的一环，下面我们就介绍一下车库门遥控器对码的方法和注意事项。

The most intuitive feeling with a garage is that you don't have to use a hot car in winter, take a sauna in summer, or worry about finding a parking spot. But it is inevitable to lose the garage remote control in daily use. Should we seek professional repair or do we have to do it ourselves? Actually, adding a remote control is very simple, as long as you learn to match the code, it can be easily solved. Code matching is a very important part of the process of adding a garage remote control. Below, we will introduce the method and precautions for code matching of garage door remote controls.

　　一、准备工作

1、 Preparation work

　　从某宝上花十几块钱买个一样的遥控器。准备个板凳要不然够不着电机盒。对码之前车库门处于关闭状态。

Spend more than ten yuan on a certain treasure to buy the same remote control. Prepare a stool, otherwise you won't be able to reach the motor box. The garage door was closed before the code was checked.

　　二、对码步骤

2、 Matching steps

　　1. 找到电机盒外壳上的“SHUTTER（百叶窗）”字样，在字样上方有上下两个箭头，分别对应遥控器的上下键。有的需要打开电机盒，电路板上有控制上下键的按钮。

1. Find the word "SHUTTER" on the outer shell of the motor box, with two arrows above the word, corresponding to the up and down keys of the remote control. Some require opening the motor box, and there are buttons on the circuit board that control the up and down buttons.

　　2. 按住电机盒的两个按键，旁边的指示灯会开始闪烁，表示电机盒已经准备就绪。

2. Press and hold the two buttons on the motor box, and the indicator light next to it will start flashing, indicating that the motor box is ready.

　　3. 再次按下手中遥控器的上下键，此时电机盒的指示灯会停止闪烁，表示对码成功。

3. Press the up and down buttons on the remote control again, and the indicator light on the motor box will stop flashing, indicating successful code matching.

　　4. 重复以上步骤，依次对其他遥控器进行对码即可。多准备几个以备不时之需。

4. Repeat the above steps and code the other remote controls one by one. Prepare more for unexpected needs.

　　三、注意事项

3、 Precautions

　　1. 在对码过程中，不要同时按下遥控器的其他按键，以免干扰对码过程。

1. During the coding process, do not press other buttons on the remote control at the same time to avoid interfering with the coding process.

　　2. 如果对码不成功，可以重新尝试或者检查电机是否工作正常。

If the code matching is not successful, you can try again or check if the motor is working properly.

　　3. 在使用遥控器控制车库门时，要确保遥控器和电机匹配一致，避免误控他人车库。

When using a remote control to control the garage door, it is important to ensure that the remote control matches the motor to avoid accidentally controlling someone else's garage.

　　如果是有自动拷贝功能的，准备新旧两把遥控器，首先长按旧遥控器上下键三秒，指示灯闪烁后松开。然后交替按下新旧遥控器的各个按键，也能匹配成功。就是清码和拷贝两个步骤。

If there is an automatic copying function, prepare two new and old remote controls. First, press and hold the up and down buttons on the old remote control for three seconds, the indicator light will flash, and then release it. Then press the various buttons of the new and old remote controls alternately, and the matching can also be successful. It consists of two steps: clearing the code and copying.

　　车库门遥控器的对码步骤虽然简单，只要正确对码，就能让遥控器正常控制车库门的开关。在使用遥控器时，需要认真阅读说明书，了解对码方法和注意事项，确保安全使用车库门遥控器。

Although the coding process for the garage door remote control is simple, as long as the coding is correct, the remote control can control the opening and closing of the garage door normally. When using the remote control, it is necessary to carefully read the manual, understand the code matching method and precautions, and ensure safe use of the garage door remote control.

本文由济南车库门为您精心提供，如想了解更多请点击我们的网站：http://www.jnyuqilin.com，我们将会以最大的热情为您解答！

This article is carefully provided by Jinan Garage Door. If you want to learn more, please click on our website: http://www.jnyuqilin.com We will answer you with the greatest enthusiasm!