电动卷帘门的安装需要注意什么？

Step 1: prepare the installation tool. Operators shall prepare electric welding machine, electric hammer, electric hand drill, ladder, drill bit, cutting head, level gauge, screwdriver and other tools and accessories.

第二步：确定电动卷帘门安装尺寸大小。作业人员在门框的位置画出线条，确定好电动卷帘门的大小，然后，让施工人员定做出合适尺寸的电动卷帘门，通常，电动卷帘门的高度要略高于门框。

Step 2: determine the installation size of the electric rolling shutter door. The operator shall draw lines at the position of the door frame to determine the size of the electric rolling shutter door, and then let the construction personnel determine the electric rolling shutter door of appropriate size. Generally, the height of the electric rolling shutter door shall be slightly higher than the door frame.

电动卷帘门怎么安装 电动卷帘门价格

How to install electric rolling shutter door price of electric rolling shutter door

第三步：确定水平线，根据现场情况来设定尺寸。作业人员在卷帘门侧板的洞口上方50厘米处，使用水平尺画出一条水平线;然后，在卷帘门的侧板跨出洞口13厘米处，使用水平尺画下一条垂直线;再把副板跨出门框的9厘米处，画出一条垂直线;将侧板固定在垂直线上，将侧板的最高处画上一条水平线。

Step 3: determine the horizontal line and set the size according to the site conditions. The operator shall draw a horizontal line 50 cm above the opening of the side plate of the rolling shutter door with a level ruler; Then, draw a vertical line with a horizontal ruler at the place where the side plate of the rolling shutter door crosses 13 cm out of the hole; Then cross the auxiliary plate 9 cm out of the door frame and draw a vertical line; Fix the side plate on the vertical line and draw a horizontal line on the highest part of the side plate.

第四步：作业人员将电机固定在主板上，再使用链条将轮盘和电机底座连接，把遥控线盒装置和电机相连接，测试卷帘门的手柄是否颠倒，如果电动卷帘门的遥控接收盒颠倒，则需要拨动内置的黑色按键。

Step 4: the operator fixes the motor on the main board, then uses the chain to connect the wheel disc with the motor base, connects the remote control wire box device with the motor, and tests whether the handle of the rolling shutter door is reversed. If the remote control receiving box of the electric rolling shutter door is reversed, it is necessary to dial the built-in black button.

第五步：电动卷帘门焊接牢固。电动卷帘门确定尺寸合适之后，将其与转轴焊接牢固，让焊接的钻头打孔保持垂直。作业人员检查电动卷帘门的电源工作是否正常，将卷帘门的轨道拉成人字，将卷帘门调成水平，确定上下水平线位置准确，再使用螺丝杆将帘子升上去。

Step 5: the electric rolling shutter door shall be firmly welded. After the size of the electric rolling shutter door is determined to be appropriate, it shall be firmly welded with the rotating shaft to keep the drilling of the welded drill vertical. The operator shall check whether the power supply of the electric rolling shutter door works normally, pull the track of the rolling shutter door into a word, adjust the rolling shutter door to be horizontal, determine the accurate position of the upper and lower horizontal lines, and then use the screw rod to raise the curtain.

第六步：检查与测试。作业人员打开电源之后，拉动电动卷帘门的开关，进行升降演示操作，确保其不会出现失灵等情况，从而造成安全事故的发生。作业人员确定电动卷帘门的轨道通畅、洁净，按钮不会出现反弹失灵等问题。

Step 6: Inspection and test. After the operator turns on the power supply, pull the switch of the electric rolling shutter door to carry out the lifting demonstration operation to ensure that it will not fail, resulting in safety accidents. The operator shall ensure that the track of the electric rolling shutter door is smooth and clean, and the button will not rebound or fail.

以上的精彩内容来自： 济南电动卷帘门安装维修提供分享，更多的精彩内容请点击进入我们的网站：http://www.jnyuqilin.com，我们会有更多的精彩内容等您查看

The above highlights come from: Jinan electric rolling shutter door installation and maintenance to share. For more highlights, please click to enter our website: http://www.jnyuqilin.com , we will have more wonderful content for you to see