保温卷帘门的使用特性介绍

Thermal insulation roller shutter door is a type of roller shutter door with special functions, which is characterized by particularly excellent thermal insulation performance. The insulation roller shutter door is formed by double layer rolling of aluminum alloy or galvanized steel plate, and the middle of the profile is filled with green and environmentally friendly foam material, which can effectively eliminate noise, improve the bending resistance of the profile, and have a good insulation effect.

保温卷帘门型材表面为多层烤漆或薄膜层，抗阳光照射抗雨水抗腐蚀抗划伤。可采用外装内装中装多种安装方式，遇微碰撞后可反弹恢复，如划伤可做到单片更换。采用管状式电机配套安装，体积小造型美观。

The surface of the insulated roller shutter door profile is made of multiple layers of baking paint or thin film, which is resistant to sunlight, rain, corrosion, and scratches. Multiple installation methods can be used, including external installation and internal installation. In case of minor collisions, it can rebound and recover. If there are scratches, it can be replaced as a single piece. Equipped with a tubular motor for installation, it has a small size and beautiful appearance.

保温卷帘门安装方法：

Installation method of insulation roller shutter door:

在安装的门框框口画线标出相应的位置，同时注明尺寸大小，需要注意的是框内高度要比门扇的高度高一些。安装在门外侧的保温卷帘门通常能使该门的K值至少提高45%，在安装时保证卷帘面板与门框的间距≥40mm。

Mark the corresponding position on the installed door frame opening with a line, and indicate the size. It should be noted that the height inside the frame should be higher than the height of the door leaf. The thermal insulation roller shutter door installed on the outside of the door can usually increase the K value of the door by at least 45%, and ensure that the distance between the roller shutter panel and the door frame is ≥ 40mm during installation.

为了将保温卷帘门的门框固定，要先拆掉门框下部的固定板，在洞口两侧的地面要事先预留凹槽，然后进行校正，待合格后固定木楔，将门框铁脚与预埋铁板件焊牢。

In order to fix the door frame of the thermal insulation rolling shutter door, the fixing plate at the bottom of the door frame should be removed first. Grooves should be reserved on the ground on both sides of the hole in advance, and then calibrated. After passing the calibration, the wooden wedge should be fixed, and the iron feet of the door frame should be welded firmly with the embedded iron plate.

安装门扇主体，注意一定要保证保温卷帘门与墙体结成整体，封闭性要做好，然后粉刷洞口及墙体。粉刷完毕后，门缝应均匀平整，开启保温卷帘门应该自由轻便，不得有过紧过松和反弹现象。

When installing the main body of the door leaf, it is important to ensure that the insulation roller shutter door is integrated with the wall, and the sealing should be done well. Then, the opening and wall should be painted. After the painting is completed, the door seam should be even and flat, and the opening of the insulation roller shutter door should be free and light, without any tightness, looseness, or rebound.

保温卷帘门安装要点：

Key points for installing insulation roller shutter doors:

保证保温卷帘门在关闭时的密封性，座条必须与接触面密闭，通常可以在其下端设置一条弹性密封型材。

To ensure the sealing of the insulation roller shutter door when closed, the seat strip must be sealed with the contact surface, and an elastic sealing profile can usually be set at its lower end.

导轨上必须有密封装置，有弹性的橡胶条或者硅化毛条，加有密封装置的导轨的宽度须与叶片的厚度相适应。

There must be a sealing device on the guide rail, with elastic rubber strips or silicified wool strips. The width of the guide rail with a sealing device must match the thickness of the blades.

为了减少从卷帘门包箱口生产的热量损失，必须使处于关闭状态的卷帘板压住卷帘包箱的外侧面，必要时在相应缝隙处加装密封条。

In order to reduce the heat loss produced from the opening of the roller shutter door packaging box, it is necessary to make the roller shutter board in the closed state press against the outer side of the roller shutter packaging box, and if necessary, install sealing strips at the corresponding gaps.

为了符合减少构件热损失的要求，需要在暗装卷帘包箱朝寅一面加上厚度在20mm以上的保温材料，缝隙处可用如密封条等密封。

In order to meet the requirements of reducing component heat loss, it is necessary to add insulation material with a thickness of 20mm or more on the inward side of the concealed roller shutter packaging box, and the gaps can be sealed with sealing strips or other materials.

本文由济南电动卷帘门安装维修为您提供，我们的网站是:http://www.jnyuqilin.com将以全心全意的热情为您提供服务，欢迎您的访问！

This article is provided for you by Jinan Electric Roller Shutter Door Installation and Maintenance. Our website is: http://www.jnyuqilin.com We will provide you with wholehearted enthusiasm and welcome your visit!