济南车库门：翻板车库门的扭簧正确安装方法

来源：http://www.jnyuqilin.com/  发布时间：2024-11-20 12:18:25

　　翻板车库门的扭簧安装方法如下：

　　The installation method of the torsion spring for the flip garage door is as follows:

　　确认洞口及产品规格 ：

　　Confirm the opening and product specifications:

　　在安装前，需要先测量车库门口的尺寸，确保门的尺寸与洞口的尺寸相匹配。

　　Before installation, it is necessary to measure the size of the garage entrance to ensure that the size of the door matches the size of the opening.

　　安装导轨 ：

　　Installation guide rail:

　　轨道应该安装在车库门口的两侧，并且需要保证水平和垂直。

　　The track should be installed on both sides of the garage entrance and ensure horizontal and vertical alignment.

　　安装左右支架 ：

　　Install left and right brackets:

　　支架安装之前要先把门洞（宽、高）和净空高度的实际尺寸测量出来，根据数据定出安装位置。

　　Before installing the bracket, the actual dimensions of the door opening (width, height) and clearance height should be measured, and the installation position should be determined based on the data.

　　用水平尺定好支架上端面平行线，支架外端点必须与导轨边侧垂直。

　　Use a level ruler to determine the parallel line on the upper end face of the bracket, and the outer endpoint of the bracket must be perpendicular to the side of the guide rail.

　　在墙壁上打孔，用膨胀螺钉把支架固定好。如果门洞超过4.2m，支架下面需加30X30mm角铁焊接与支架成三角形，以增加支架的承载力。

　　Drill holes in the wall and secure the bracket with expansion screws. If the door opening exceeds 4.2m, a 30X30mm angle iron should be welded to the bracket to form a triangle, in order to increase the load-bearing capacity of the bracket.

　　门体上支架及安装固定 ：

　　Door bracket and installation fixing:

　　先根据门洞的实际宽度，定好中轴长度，抬上手摇升降车（注意门体旋转的方向，门应从打开的前面旋转下来），一直升到支架上面。

　　First, determine the length of the central axis based on the actual width of the door opening, lift the hand cranked lifting car (pay attention to the direction of rotation of the door body, the door should rotate down from the front when opened), and lift it all the way up to the bracket.

　　门体上支架后，粗略地装U型螺丝，鞍形铁座和螺帽安装到支架上（暂时不要拧紧螺丝）。

　　After installing the bracket on the door body, roughly install the U-shaped screws, saddle iron seat, and nut onto the bracket (do not tighten the screws temporarily).

　　调试弹簧 ：

　　Debugging springs:

　　扭簧的一端与固定法兰和中心支架用M8螺栓组连接。

　　One end of the torsion spring is connected to the fixed flange and center bracket with an M8 bolt assembly.

　　用专用工具调整杆调整扭簧的圈数，待调整到合适的圈数后，把调整杆靠在墙上，以防止扭簧反弹松动。

　　Use a special tool to adjust the number of turns of the torsion spring. After adjusting to the appropriate number of turns, place the adjustment rod against the wall to prevent the torsion spring from rebounding and loosening.

　　卷门开闭调试 ：

　　Rolling door opening and closing debugging:

　　调整绳轮：将钢丝绳底部与底轮支架套好，用两个钢丝绳扣锁紧，钢丝绳从上至下应在所有滚轮内侧。上边在绳轮上预存两圈，然后穿过绳轮的孔打结。

　　Adjust the pulley: Cover the bottom of the steel wire rope with the bottom pulley bracket, and lock it with two steel wire rope buckles. The steel wire rope should be on the inside of all rollers from top to bottom. Pre store two loops on the pulley and tie the knot through the hole on the pulley.

　　根据门口高度按绳轮有效直径计算轮周长，算出绳轮运行圈数，在计算结果上增加1.5-2圈，待钢丝拉紧后将绳轮顶丝紧固。

　　Calculate the circumference of the pulley based on the effective diameter of the rope pulley according to the height of the doorway, and calculate the number of rotations of the rope pulley. Add 1.5-2 rotations to the calculation result, and tighten the top wire of the rope pulley after the steel wire is tightened.

　　反复用手把门抬起落下，观察门体上下运行是否灵活。当抬起或拉下门体时，松手即停，并且手动时的提升力应不大于120N，说明扭簧已调节完毕。

　　Repeatedly lift and lower the door with your hand, and observe whether the door moves up and down flexibly. When lifting or pulling down the door, release it to stop, and the lifting force during manual operation should not exceed 120N, indicating that the torsion spring has been adjusted.

　　限位安装 ：

　　Limit installation:

　　限位安装是为了确保门体在开启和关闭时能够到达合适的位置。

　　The limit installation is to ensure that the door can reach the appropriate position when opening and closing.

　　门锁安装及调试 ：

　　Door lock installation and debugging:

　　车库门的锁安装也是重要的一环，需要确保其功能正常。

　　The installation of the garage door lock is also an important part, ensuring its proper functioning.

　　填写安装日期 ：

　　Fill in installation date:

　　最后，记录安装完成的日期。

　　Finally, record the date of installation completion.

　　以上步骤仅供参考，具体安装过程中可能需要根据实际情况进行调整。建议在专业人员的指导下进行安装，以确保安全和效果。

　　The above steps are for reference only, and adjustments may need to be made according to the actual situation during the installation process. It is recommended to install under the guidance of professionals to ensure safety and effectiveness.

　　本文来自：更多的内容请点击：http://www.jnyuqilin.com我们将会为您提问的问题提供一个满意的服务，欢迎您的来电！

　　This article is from: Jinan Garage Doors. For more content, please click: http://www.jnyuqilin.com We will provide satisfactory service for the questions you ask. Welcome to call us!