如何调节电动卷帘门的限位器？

Electric rolling shutter door is often used in our life. How to adjust the limiter of Jinan electric rolling shutter door has been perplexing many customers. Let's introduce the adjustment method of roller shutter door limiter.

济南电动卷帘门

Jinan electric rolling shutter door

电动卷帘门一般有两个限位开关。一个是上限，另一个是下限。限位开关应具械旋转杆，以控制开关的端部和打开。调整时，应由两人操作。一人可以调整顶部机械旋转杆的位置，另一人可以控制电动卷帘门的上下位置，配合限位开关位置的调整。

The electric rolling shutter door generally has two limit switches. One is the upper limit and the other is the lower limit. Limit switches shall be equipped with mechanical rotating rods to control the end and opening of the switch. When adjusting, it should be operated by two people. One person can adjust the position of the top mechanical rotating rod, and the other person can control the up and down position of the electric rolling shutter door to cooperate with the adjustment of the position of the limit switch.

电动卷帘门限调试方法：

Commissioning method of electric rolling shutter threshold:

1.将止动块上的螺母卡箍转动到适当的方向，以分离螺母塞，或松开止动块上的夹紧螺钉。

1. Turn the nut clamp on the stop block to the appropriate direction to separate the nut plug or loosen the clamping screw on the stop block.

2.打开车门至正确位置，转动限位器上的限位螺母，按下车门开启限位开关上的滚轮。听到“咔嗒”声后，将螺母卡入相应的限位螺母或拧紧螺钉。

2. Open the door to the correct position, turn the limit nut on the limiter, and press the roller on the door opening limit switch. After hearing the "click", clip the nut into the corresponding limit nut or tighten the screw.

3.将车门关闭到适当位置，转动限位器上的限位螺母，并按下关闭限位开关上的滚轮。听到“咔嗒”声后，将螺母卡入相应槽中的限位螺母或拧紧螺钉。

3. Close the door to the proper position, turn the limit nut on the limiter and press the roller on the closing limit switch. After hearing the "click", clip the nut into the limit nut in the corresponding slot or tighten the screw.

4.如果门的位置不合适，可以将其再次调整到合适的位置。

4. If the position of the door is not appropriate, it can be adjusted to the appropriate position again.

电动卷帘门的设置要求：

Setting requirements for electric rolling shutter door:

1.当吊钩滑动到限位置时，提升操纵杆。当按下限位开关时，电源关闭，只有在箱子关闭时才能降下吊钩。

1. When the hook slides to the limit position, lift the control lever. When the limit switch is pressed, the power is turned off, and the hook can be lowered only when the box is closed.

2.在轨道边缘安装固定限位挡板(在控制装置限制的位置)。当塔式起重机运行到此位置时，限位挡板接触行程开关手柄并断开电源以控制行程。重合闸时，塔机只能反向运行。

2. Install a fixed limit baffle at the edge of the track (at the position limited by the control device). When the tower crane runs to this position, the limit baffle contacts the travel switch handle and disconnects the power supply to control the travel. During reclosing, the tower crane can only operate in reverse.

3.在光盘中安装一个垂直移动的指针。当振幅改变时，指针指示各种振幅下的额定起重能力。当臂杆移动到上、下限位时，分别按住限位开关，断开控制电路，变幅电机停止，实现限位功能。

3. Install a vertically moving pointer in the disc. When the amplitude changes, the pointer indicates the rated lifting capacity at various amplitudes. When the arm moves to the upper and lower limits, press and hold the limit switch respectively, disconnect the control circuit, and the luffing motor stops to realize the limit function.

本文由济南电动卷帘门安装维修为您提供，我们的网站是：http://www.jnyuqilin.com我们将以全心全意的热情为您提供服务，欢迎您的访问

This article is provided for you by Jinan electric rolling shutter door installation and maintenance. Our website is: http://www.jnyuqilin.com We will serve you with wholehearted enthusiasm. Welcome to visit