济南卷帘门帘及易锈部位的保养处理

Rolling shutter doors have safety functions. The wind resistance function is widely used and has a broad market prospect. The following Chongqing Rolling shutter Door Factory introduces the composition and structure of rolling shutter doors: The function of rolling shutter doors is determined by different components.

现在，卷帘门的组成部分首要包括自动控制设备。由门结构、聚氯乙烯窗帘、驱动电机、控制系统等组成。在此期间，一些原材料的运用是不同的，其功用是不同的。

Now, the components of roller shutter doors mainly include automatic control equipment. Composed of door structure, PVC curtains, drive motor, control system, etc. During this period, the use of some raw materials varied and their functions varied.

卷帘门扇颤抖：

Rolling shutter door leaf trembles:

或许是由于地下导轨或止摆器有障碍物或磨损。

Perhaps it is due to obstacles or wear on the underground guide rails or swing stops.

或移动吊摆和轨迹磨损或障碍物。

Or move the pendulum and track wear or obstacles.

卷帘门开关速度过慢：

Rolling shutter door switch speed too slow:

控制器速度调整太慢。

The controller speed adjustment is too slow.

电压异常。

Abnormal voltage.

皮带或许过度松动。

The belt may be excessively loose.

止动轮与轨迹发生冲突。

The stop wheel conflicts with the trajectory.

怎么正确运用电动卷帘门？

How to use electric roller shutter doors correctly?

合理的提高速度能够减少动力糟蹋和传动部件的冲突丢失，也有助于延长变频器的运用寿命。这能够根据实际需要设置电动卷帘门的开关速度。

Reasonable increase in speed can reduce power waste and conflict loss of transmission components, and also help extend the service life of frequency converters. This can set the opening and closing speed of the electric roller shutter door according to actual needs.

卷帘门运转时，制止在下面行走，卷帘门下梁下端制止堆放物品。

When the rolling shutter door is in operation, stop walking below and stop stacking items at the bottom of the lower beam of the rolling shutter door.

卷帘门帘及易锈部位，要定时油漆及防绣保养，制止用重物.硬物冲击门面。

Rolling shutter doors, curtains, and easily rusted areas should be regularly painted and maintained for rust prevention, and heavy or hard objects should be avoided from impacting the facade.

在卷帘门装置方位的上端，应有可靠的防火设备。在卷帘门卷筒下端制作包装箱或天花板时，应设置可拆卸活动盖板。电动卷帘机一侧下端必须预留500×500mm可拆卸修理孔，便于修理。

At the upper end of the rolling shutter door device, there should be reliable fire protection equipment. When making packaging boxes or ceilings at the lower end of the roller shutter door drum, removable movable cover plates should be installed. 500 must be reserved at the lower end of one side of the electric roller shutter machine × 500mm detachable repair hole for easy repair.

电动卷帘门在启闭中止过程中，应具有随地中止的功用，不得中止并持续下滑。中山道尔自动门窗提醒，假如下滑间隔大于50mm，应立即仔细检查和修理卷帘门控制电器和卷帘门机制动器，直至正常运转。

Electric roller shutter doors should have the function of stopping anywhere during the opening and closing process, and should not stop and continue to slide. Zhongshan Daoer Automatic Doors and Windows reminds that if the sliding interval is greater than 50mm, the control electrical appliances and brake of the rolling shutter door should be carefully inspected and repaired immediately until it operates normally.

假如电动卷帘门关闭后简单自开，既不便利又不安全，能够找一块尺度适宜的强磁铁，平埋在门框上方约1/4的门高，然后在门扇与门框一致的地方钉一块铁皮，防止不锈钢卷帘门自开。

If the electric roller shutter door simply opens on its own after closing, it is neither convenient nor safe. You can find a strong magnet with a suitable scale, buried about 1/4 of the door height above the door frame, and then nail a piece of iron sheet at the same place as the door leaf and frame to prevent the stainless steel roller shutter door from opening on its own.