电动卷帘门在停电的情况下如何打开？

Electric roller shutter door often appears in daily life, for example, garage, shops will choose electric roller shutter door, which is not only very safe but also very convenient. Today, I'd like to introduce the common problems and installation steps of the electric rolling shutter door in detail.

电动卷帘门没电怎么办?

How to do without electricity for electric rolling shutter door?

1、停电时门开着的,去拉电机上的一条链子,费一点时间就可以关上门。但是人就会被关在室内。

1. When the power is off, the door is open. Go and pull a chain on the motor. It takes a little time to close the door. But people will be locked in.

2、停电时门关着的,人又在室内,去拉电机上的一条链子,费一点时间就可以打开门。

2. When the power is off, the door is closed, and the person is in the room. Go to pull a chain on the motor, and it takes a little time to open the door.

3、停电时门关着的,人又在室外,只有等到来电才解决。在进行卷帘门安装的时候,可以安装不间断的电源比如后备电源,这样遇到停电时就不用担心了。

3. When the power is off, the door is closed, and the person is outside. It can only be solved when the power is on. When installing the rolling shutter door, you can install uninterruptible power supply, such as backup power supply, so that you don't have to worry about power failure.
                              

电动卷帘门安装步骤：

Installation steps of electric rolling shutter door:

1、先在需要安装的门框框口位置画出线。表明尺寸大小，然后找工作人员设计出合适的电动卷帘门，这里值得注意的一点是框内高度比门扇的高度要高一点点。

1. First, draw the outgoing line at the position of the door frame to be installed. Show the size, and then find the staff to design a suitable electric roller shutter door. It is worth noting that the height of the frame is a little higher than that of the door leaf.

2、先把电动卷帘门的门框固定，这里要先拆掉门框下部的固定板。(注意：洞口两侧地面要预留凹槽，经校正合格后，固定木楔，门框铁脚与预埋铁板件焊牢。用水泥砂浆或强度不低于10MPa细石混凝土嵌塞牢固即可。)

2. First, fix the frame of the electric rolling shutter door. Here, first remove the fixing plate at the lower part of the frame（ Note: grooves shall be reserved on the ground at both sides of the hole. After the correction is qualified, the wooden wedge shall be fixed, and the iron foot of the door frame shall be firmly welded with the embedded iron plate. Cement mortar or fine aggregate concrete with strength not less than 10MPa can be used to firmly plug.)

3、安装电动卷帘门扇主体门扇。一定要保证电动卷帘门与墙体结成整体，封闭性要做好，再粉刷洞口及墙体。粉刷完毕后，门缝应均匀平整，开启电动卷帘门应该自由轻便，不得有过紧、过松和反弹现象。

3. Install the main door leaf of electric rolling shutter door leaf. We must ensure that the electric rolling shutter door and the wall form a whole, the sealing should be done well, and then paint the hole and the wall. After painting, the door seam should be even and smooth, and the opening of the electric roller shutter door should be free and light, without too tight, too loose and rebound phenomenon.

感谢您的阅读，希望以上内容能对您有所帮助，如您想了解更多精彩内容请点击我们的官网：济南电动卷帘门安装维修http://www.jnyuqilin.com。

Thank you for reading, I hope the above content can help you, if you want to know more wonderful content, please click our official website: Jinan electric roller shutter door installation and maintenance http://www.jnyuqilin.com .