快速门安全底边保护功能特点

安全底边在各种快速门和工业门中非常常见，其安全保护功能极强，尤其是近两年用户最青睐的快速门，安全底边也是其标准配置之一。安装后，为了保证其功能的正常使用，需要进行相关的功能测试，以保证其在保护用户方面发挥应有的作用。

The safety bottom edge is very common in all kinds of fast doors and industrial doors, and its safety protection function is very strong, especially the fast door most favored by users in recent two years. The safety bottom edge is also one of its standard configurations. After installation, in order to ensure the normal use of its functions, relevant functional tests need to be carried out to ensure that it plays its due role in protecting users.

安装快速门安全底边时，先将底边盒连接线接到电气柜端子上，按标准编号连接。注意：当电控柜内没有GND终端点时，将通讯线连接到g点，这样当门落地后碰到压力管底边时，就会收到信号。当COM线接在X5时，落地后碰到压力管底边，所以收不到信号。

When installing the safety bottom edge of the fast door, first connect the connecting wire of the bottom edge box to the terminal of the electrical cabinet and connect it according to the standard number. Note: when there is no GND terminal point in the electric control cabinet, connect the communication line to point G, so that when the door touches the bottom edge of the pressure pipe after landing, it will receive the signal. When the com line is connected to X5, it touches the bottom edge of the pressure pipe after landing, so the signal cannot be received.

安装调试后，需要对其功能进行测试，快速门分析具体测试步骤如下：

After installation and commissioning, its function needs to be tested. The specific test steps of fast door analysis are as follows:

关闭紧急停止按钮并打开电源。按下底部接收器面板上的学习按钮一次，信号接收器亮起。

Turn off the emergency stop button and turn on the power. Press the learning button on the bottom receiver panel once and the signal receiver lights up.

按压底部布口袋中的压力软管数次，信号接收器指示灯闪烁，成功接收记忆。反复按下底部压力软管，每次信号连接完成时，接收器灯亮一次。

Press the pressure hose in the bottom cloth pocket several times, the signal receiver indicator flashes, and the memory is successfully received. Press the bottom pressure hose repeatedly, and the receiver light comes on once each time the signal connection is completed.

打开电气柜的急停按钮，按下底部布口袋中的压力软管。当哈尔滨快速门收到信号后，会自动上升，正常运行。

Open the emergency stop button of the electrical cabinet and press the pressure hose in the bottom cloth pocket. When Harbin express door receives the signal, it will rise automatically and operate normally.

在测试和使用安全底边的过程中，如果发现电控柜接收不到安全底边信号，需要检查安全底边变送器和底边压力软管中的电池，看电池是否耗尽，如果耗尽，更换新的。检查底部压力软管是否损坏或泄漏。如果损坏或泄漏，将其密封。如有必要，用新的安全底部压力软管更换。

In the process of testing and using the safety bottom, if it is found that the electric control cabinet cannot receive the safety bottom signal, it is necessary to check the battery in the safety bottom transmitter and bottom pressure hose to see if the battery is exhausted. If it is exhausted, replace it with a new one. Check the bottom pressure hose for damage or leakage. If damaged or leaking, seal it. If necessary, replace with a new safety bottom pressure hose.