电动卷帘门极限调试方法与设置要求

现如今，越来越多的人会用济南电动卷帘门来代替商店里的卷帘门。操作起来更加方便，人们在使用的时候也不会有太大的负担。下面和济南电动卷帘门安装维修厂家一起来了解一个问题--电动卷帘门极限调试方法与设置要求。

Nowadays, more and more people will use Jinan electric roller shutter doors to replace the roller shutter doors in stores. It is more convenient to operate, and people will not have too much burden when using it. Now let's work with Jinan electric roller shutter door installation and maintenance manufacturer to understand a problem -- limit commissioning method and setting requirements of electric roller shutter door.

电动卷帘门极限调试方法：

Limit commissioning method of electric roller shutter door:

1.将止动块上的螺母卡箍转动到适当的方向，以分离螺母塞，或松开止动块上的夹紧螺钉。

1. Turn the nut clamp on the stopper to the proper direction to separate the nut plug or loosen the clamping screw on the stopper.

2.打开车门至正确位置，转动限位器上的限位螺母，按下车门开启限位开关上的滚轮。听到“咔嗒”声后，将螺母卡入相应的限位螺母或拧紧螺钉。

2. Open the door to the correct position, turn the limit nut on the limit switch, and press the roller on the door opening limit switch. After hearing the "click" sound, clip the nut into the corresponding limit nut or tighten the screw.

3.将车门关闭到适当位置，转动限位器上的限位螺母，并按下关闭限位开关上的滚轮。听到“咔嗒”声后，将螺母卡入相应槽中的限位螺母或拧紧螺钉。

3. Close the door to the proper position, turn the limit nut on the limiter, and press the roller on the closing limit switch. After hearing the "click" sound, clip the nut into the limit nut in the corresponding slot or tighten the screw.

4.如果门的位置不合适，可以将其再次调整到合适的位置。

4. If the position of the door is not appropriate, it can be adjusted to the appropriate position again.

电动卷帘门的设置要求：

Requirements for setting of electric roller shutter door:

1.当吊钩滑动到极限位置时，提升操纵杆。当按下限位开关时，电源关闭，只有在箱子关闭时才能降下吊钩。

1. When the hook slides to the limit position, lift the control lever. When the limit switch is pressed, the power is off, and the hook can only be lowered when the box is closed.

2.在轨道边缘安装固定限位挡板(在控制装置限制的位置)。当塔式起重机运行到此位置时，限位挡板接触行程开关手柄并断开电源以控制行程。重合闸时，塔机只能反向运行。

2. Install fixed limit baffle at the edge of the track (at the position limited by the control device). When the tower crane runs to this position, the limit baffle contacts the travel switch handle and disconnects the power supply to control the travel. During reclosing, the tower crane can only operate in reverse direction.

3.在光盘中心安装一个垂直移动的指针。当振幅改变时，指针指示各种振幅下的额定起重能力。当臂杆移动到上、下限位时，分别按住限位开关，断开控制电路，变幅电机停止，实现限位功能。

3. Install a vertically moving pointer in the center of the disc. When the amplitude changes, the pointer indicates the rated lifting capacity under various amplitudes. When the boom moves to the upper and lower limit positions, press and hold the limit switch respectively, disconnect the control circuit, and the luffing motor stops to realize the limit function.

以上是电动卷帘门极限调试方法与设置要求的相关内容。希望它能帮助您。如果您想了解更多关于门的知识，欢迎关注我们http://www.jnyuqilin.com以获取更多信息。

The above is related to the limit commissioning method and setting requirements of electric roller shutter door. I hope it can help you. If you want to know more about doors, please follow us http://www.jnyuqilin.com For more information.