电动卷帘门的具体安装技术要求

电动卷帘门在一定时间内，连同框架能满足耐火稳定性和完整性要求的卷帘，由帘板、卷轴、电动机、导轨、支架、防护罩和控制机构等组成。具体安装技术要求如下：

Within a certain period of time, the electric roller shutter, together with the roller shutter whose frame can meet the requirements of fire resistance stability and integrity, is composed of curtain plate, roller, motor, guide rail, bracket, protective cover and control mechanism. The specific installation technical requirements are as follows:

A、导轨：导轨应相互平行、垂直，其平行、垂直度误差不大于5mm；导轨顶部必须用F形扳手折成圆弧形，固定导轨用膨胀角码间距应在600mm以内且同一层区域内导轨固定点高度应一致，导轨上端应与支架板下口齐平，距离不大于50mm。

A. Guide rail: the guide rail shall be parallel and vertical to each other, and the error of parallelism and perpendicularity shall not be greater than 5mm; The top of the guide rail must be folded into an arc shape with an F-shaped wrench. The spacing of the expansion angle code used to fix the guide rail should be within 600mm, and the height of the fixed point of the guide rail in the same layer area should be consistent. The upper end of the guide rail should be flush with the lower opening of the support plate, and the distance should not be greater than 50mm.

B、转轴及支架板：两端支架板必须在同一水平上且纵向互平行，误差不得超过5mm，主支架背后支撑不少于两道，副支架背后必须有支撑以保证转轴平稳运转。副板处转轴轴托必须实焊满焊。（支架板支撑用角钢，统一采用5#镀锌角钢）双帘的两根转轴挂钩螺丝必须调到同一平面上。

B. Rotary shaft and support plate: the support plates at both ends must be at the same level and parallel to each other longitudinally, with an error of no more than 5mm. The back of the main support must have at least two supports, and the back of the auxiliary support must have support to ensure the smooth operation of the rotary shaft. The shaft bracket at the auxiliary plate must be fully welded. (Angle steel is used for support of support plate, and 5 # galvanized angle steel is uniformly used) The two pivot hook screws of double curtain must be adjusted to the same plane.

C、帘面：济南电动卷帘门安装维修人员认为，须用挂钩片与转轴连接并拧紧螺母，挂钩片之间距不大于1000mm，帘面两端各嵌入导轨深度不小于50mm；底梁与门帘间连接必须牢固灵活，帘面表面必须保持干净整洁。帘面调试后底梁必须保持水平并平行运行。

C. Curtain surface: Jinan electric roller shutter door installation and maintenance personnel believe that it is necessary to use the hook piece to connect with the rotating shaft and tighten the nut. The distance between the hook pieces is not more than 1000mm, and the depth of the embedded guide rail at both ends of the curtain surface is not less than 50mm; The connection between the sill and the door curtain must be firm and flexible, and the curtain surface must be kept clean and tidy. After curtain commissioning, the sill must be kept horizontal and run in parallel.

D、封堵门楣：固定点必须用膨胀角码固定，固定点间距≤1000mm，封堵下口必须在轨道上口往下100mm处，两端必须用4#角铁与墙面固定，遇到上部有管道、桥架等障碍物穿过处，必须确保密封、平整。封堵整体平面必须要干净、平整。

D. Blocking the lintel: the fixing point must be fixed with expansion angle code, and the spacing between the fixing points is ≤ 1000mm. The lower opening of the blocking must be 100mm below the upper opening of the track, and both ends must be fixed with 4 # angle iron to the wall. When encountering obstacles such as pipes and bridges passing through the upper part, the sealing and leveling must be ensured. The overall sealing plane must be clean and flat.

E：防火包箱：包箱两端的支撑架必须采用4#角铁在地面制作完成，转角处必须成90度角。中间包箱支架采用2.5角钢制作，各支架间距不得大于2000mm（宽度再小中间必须加支架）。包箱电机行程检修口尺寸为宽500mm×300mm（竖向6片活动做成侧拉式，上下用2.5角铁固定当作抽屉式轨道），包箱下平面链条检修口尺寸100mm×88mm（横向活动式1片，前端与包箱体串接）。包箱整体必须要干净、平直。

E: Fireproof packing box: the support frame at both ends of the packing box must be fabricated on the ground with 4 # angle iron, and the corner must be at a 90 degree angle. The tundish box support is made of 2.5 angle steel, and the spacing between the supports shall not be greater than 2000mm (if the width is smaller, the support must be added in the middle). The size of the travel access hole of the package motor is 500mm wide × 300mm (6 pieces of vertical movement are made into side pull type, and 2.5 angle iron is used to fix the upper and lower parts as drawer type rail), and the dimension of the plane chain access hole under the package box is 100mm × 88mm (1 piece of horizontal movable type, with the front end connected in series with the package body). The whole package must be clean and straight.

F、电机、控制箱、按钮盒、熔断器：

F. Motor, control box, button box, fuse:

①、电机链条张紧轮必须安装且安装在电机与链轮中间的下方。电机强弱电金属软管必须分开且整齐连接至控制器。

① The chain tensioner of the motor must be installed under the middle of the motor and sprocket. The strong and weak current metal hoses of the motor must be separated and neatly connected to the controller.

②、控制器必须由两个膨胀螺栓固定牢固，且金属软管必须用塑料接头与控制箱连接。安装初步调试完毕后随手把控制箱内的所有电源关闭并锁门，外观平直；

② The controller must be fixed firmly by two expansion bolts, and the metal hose must be connected to the control box with plastic connectors. After the installation and preliminary commissioning, turn off all power supplies in the control box and lock the door with a flat and straight appearance;

③、按钮开关安装高度必须一致，具体高度1.4米左右，按钮盒安装必须用螺丝固定，不能电焊，外观要保持干净、整齐、无破损，安装完毕后统一上锁，钥匙统一带回公司；

③ The installation height of the button switch must be the same, with the specific height of about 1.4 meters. The button box must be fixed with screws instead of electric welding. The appearance should be kept clean, tidy and free of damage. After installation, the key should be locked uniformly and brought back to the company;

④、熔断器统一安装于电机侧包厢正面的角钢上同一位置且与角钢保持平行，熔断器的钢丝绳要捋平用塑料扎带固定，保证不卷入其他部位。

④ The fuse shall be uniformly installed at the same position on the angle steel on the front of the box at the motor side and kept parallel with the angle steel. The wire rope of the fuse shall be smoothed and fixed with plastic ties to ensure that it is not involved in other parts.

电动卷帘门的制作要求较高，即要求整个系统能经受一定时间的1100°左右高温考验，电动卷帘门的耐火时间是电动卷帘门的主要指标。更为详细的内容就来我们网站http://www.jnyuqilin.com咨询吧！

The manufacturing requirements of the electric rolling shutter door are high, that is, the whole system is required to withstand the high temperature test of about 1100 ° for a certain time. The fire resistance time of the electric rolling shutter door is the main index of the electric rolling shutter door. Come to our website for more details http://www.jnyuqilin.com Ask!