济南卷帘门：调试快速卷帘门的步骤

来源：http://www.jnyuqilin.com/  发布时间：2024-11-23 15:45:40

　　快速卷帘门控制箱的调试步骤如下：

　　The debugging steps for the fast rolling shutter door control box are as follows:

　　上下限位调试检测 ：

　　Upper and lower limit debugging and testing:

　　门体静止状态下，按下上升按键，门体向上运行，待经过缓冲、完全停止后，判断提升高度是否满足使用方要求。如不满足要求，再次进行调试；

　　When the door is in a stationary state, press the up button to move the door upwards. After buffering and complete stop, determine whether the lifting height meets the user's requirements. If the requirements are not met, debug again;

　　事后，按下降按键，待门体下落完全停止后，观察门体末端停留位置是否自然得体。

　　Afterwards, press the descent button and wait for the door to completely stop falling. Observe whether the end of the door stays in a natural and appropriate position.

　　急停按钮性能检测 ：

　　Emergency stop button performance testing:

　　门体运行过程中，按下急停按钮，观察门体是否立即停止。若依旧正常运行，则需检查急停按钮是否失灵或损坏。

　　During the operation of the door, press the emergency stop button and observe whether the door stops immediately. If it still operates normally, it is necessary to check whether the emergency stop button is malfunctioning or damaged.

　　自动开启功能调试 ：

　　Debugging of automatic activation function:

　　利用车辆、人员移动来模拟实际状况，观察门体是否能够及时开启，以及是否全角度无死角信号覆盖。

　　Simulate the actual situation by using vehicle and personnel movements, observe whether the door can be opened in a timely manner, and whether there is no blind spot signal coverage from all angles.

　　红外防砸性能调试 ：

　　Infrared anti smashing performance debugging:

　　在门体下落过程中，切断红外对射系统，看门体是否会及时反弹上升。在测试过程中，应及时联系工业快速门厂家，要注意自身安全，防止红外系统失灵造成砸伤情况。

　　Will the door rebound and rise in a timely manner when the infrared radiation system is cut off during the process of the door falling. During the testing process, it is necessary to promptly contact the industrial rapid door manufacturer, pay attention to personal safety, and prevent the infrared system from malfunctioning and causing injury.

　　控制箱电源检查 ：

　　Control box power supply inspection:

　　检查控制箱的电源是否正常，确保电源接线正确。

　　Check if the power supply of the control box is normal and ensure that the power wiring is correct.

　　参数设置 ：

　　Parameter settings:

　　根据快速门的要求，设置控制箱的参数，如开门速度、关门速度等。

　　According to the requirements of the fast door, set the parameters of the control box, such as opening speed, closing speed, etc.

　　传感器连接 ：

　　Sensor connection:

　　连接控制箱与快速门的传感器，确保传感器的信号正常。

　　Connect the sensor between the control box and the quick door to ensure that the sensor signal is normal.

　　手动测试 ：

　　Manual testing:

　　通过控制箱的按钮或遥控器，测试快速门的开关门功能，确保控制箱的调试成功。

　　Test the opening and closing function of the fast door through the buttons or remote control of the control box to ensure successful debugging of the control box.

　　安全性能测试 ：

　　Security performance testing:

　　调试完成后，还需进行安全性能测试，确保快速门的运行安全可靠。

　　After debugging is completed, safety performance testing is also required to ensure the safe and reliable operation of the fast door.

　　限位开关类型设置 ：

　　Limit switch type setting:

　　首次开机时，系统会提示进行限位调试相关设置，需设置限位开关类型，点击“绝对值式”，然后点击“确定”按钮。

　　When starting up for the first time, the system will prompt for limit debugging related settings. You need to set the limit switch type, click "absolute value", and then click the "OK" button.

　　开门按钮转向确认 ：

　　Confirm the direction of the door opening button:

　　按控制柜上的“开门”按钮，确认门体运行方向与实际开门方向是否一致。如果不一致，请点击“换向”，系统会自动反转电机的转向，再次进行确认后点击“确定”。

　　Press the "Open Door" button on the control cabinet to confirm whether the direction of the door's movement is consistent with the actual opening direction. If there is inconsistency, please click "Reverse Direction", and the system will automatically reverse the direction of the motor. After confirming again, click "OK".

　　上下限位设定 ：

　　Upper and lower limit setting:

　　点动下降，调整门到下限位。按住急停按钮，按住下降按钮2~4秒。变频器出现ATO提示，下限调试完毕。

　　Tap down and adjust the door to the lower limit. Press and hold the emergency stop button, and press and hold the descent button for 2-4 seconds. The frequency converter shows an ATO prompt, and the lower limit debugging is completed.

　　点动上升，调整门到上限位置。按住急停按钮，按住下降按钮2~4秒。变频器出现ATO提示，上限调试完毕。

　　Tap up and adjust the door to the upper limit position. Press and hold the emergency stop button, and press and hold the descent button for 2-4 seconds. The frequency converter shows an ATO prompt, and the upper limit debugging is completed.

　　建议按照上述步骤进行调试，并在测试过程中注意安全，确保快速卷帘门的正常运行和安全性。

　　It is recommended to follow the above steps for debugging and pay attention to safety during the testing process to ensure the normal operation and safety of the fast rolling shutter door.

　　本文由济南卷帘门为您提供，我们的网站是：http://www.jnyuqilin.com我们将以全心全意的热情为您提供服务，欢迎您的访问！

　　This article is provided by Jinan Rolling Shutter Doors. Our website is: http://www.jnyuqilin.com We will provide you with wholehearted enthusiasm and welcome your visit!